Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 14 - Jul 19
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Subaru Impreza/WRX/STi 1st/2nd Gen, Saab 9-2X Driveshaft Center Support Bearing Carrier Upgrade (SUB03A0)Holds the driveshaft where it should be. Isolation dampers minimize vibrations. Fits 1st 2nd generation Impreza variants (all), including WRX, WRX STi, 95 97 Impreza Outback, and 01 07 Outback Sport The stock center support bearing carrier holds the driveshaft in place with rubber so thin about 20 lbs of force moves it from center to the end of its travel. While thats great for making sure no NVH makes it to the cabin, it doesnt keep the bearing
Holds the driveshaft where it should be. Isolation dampers minimize vibrations.
Fits 1st/2nd generation Impreza variants (all), including WRX, WRX STi, 95-97 Impreza Outback, and 01-07 Outback Sport
The stock center support bearing carrier holds the driveshaft in place with rubber so thin about 20 lbs of force moves it from center to the end of its travel. While that’s great for making sure no NVH makes it to the cabin, it doesn’t keep the bearing centered well under load, allows the bearing to sag over time and ruin the driveshaft alignment, and creates slop in the driveline during shifts and throttle application. Over time the OEM bushing sags and becomes brittle, eventually dry rotting and cracking. Even on the best-kept cars, the stock bushing can start to from cracks in as little as 5-10 years. When the bushing lets go, it can lead to excessive vibration and clunking and put more stress on the bearing. To make matters worse, the stock carrier is molded onto the center support bearing, so it’s not easy to replace without special tools.
The videos below were recorded on a 2005 WRX STi. The bearing on this vehicle has sagged all the way to the bottom, resting on the carrier frame. The shaft is not well-supported by the soft OEM carrier, so it’s allowed to travel off-center during rapid loading and unloading.
This upgraded unit keeps the driveshaft firmly in place at all times, and its solid construction ensures it will never wear out. The thick bushings ensure the driveshaft cannot move from center, maintaining driveshaft alignment at all times.
Two options are available for the bushings, both of which are many times over better than the stock bushing. We’ve paid close attention to the NVH levels associated with this upgrade. After extensive design iterations, we’ve come up with custom isolator bushings that separate the carrier from the body of the vehicle and mounting hardware. These carriers substantially reduce NVH levels.
The street bushings absorb most of the NVH from the drivetrain. Some light NVH is possible at some speeds in the form of a soft hum. With a modified exhaust or windows down you’ll probably never hear it.
The track bushings are for those who want no-compromise drivetrain performance. These may create a substantial amount of cabin noise. Not sure which is for you? They’re interchangeable so you can try them both.
Installation doesn’t require removal of the driveshaft. The 2-part design clamps around the OEM bearing. The old carrier must be removed, so a cutting tool is required. Below are example installation videos on 2008 and 2022 models. A model-specific installation video will be released before preorders are shipped. The exact steps to access the carrier will vary slightly by model, but the removal and installation of the new carrier are the same. The basic steps are:
- Remove any braces or splash shields preventing exhaust and heat shield removal
- Remove or lower exhaust in area of center support bearing if needed for access
- Remove heat shielding covering center support bearing
- Cut off OEM carrier and remove rubber support material with razorblade, leaving base layer of rubber intact on the bearing
- Clamp new carrier around OEM bearing
- 1st gen Impreza (GM/GC/GF) (1993-1999) (all including Impreza Outback)
- 2nd gen Impreza models (GD/GG) (2000-2007) (all including WRX, WRX STi, and Outback Sport)
- 1st gen Legacy (BC/BF/BJ) (1989-1994)
- Saab 9-2X
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy