Howard Restor-A-Finish

Howard Restor-A-FinishRestor A Finish is a unique finish penetrating formula that restores wood finishes while blending out minor scratches, blemishes and abrasions With a simple wipe on, wipe off process, most finished wood surfaces that seem to need a complete refinishing job can be restored in a few minutes Removes white heat rings and water marks, sun fade, oxidation, smoke damage and most other blemishes Restor A Finish restores the finish without removing any of the

Restor-A-Finish is a unique finish-penetrating formula that restores wood finishes while blending out minor scratches, blemishes and abrasions With a simple wipe-on, wipe-off process, most finished wood surfaces that seem to need a complete refinishing job can be restored in a few minutes Removes white heat rings and water marks, sun fade, oxidation, smoke damage and most other blemishes Restor-A-Finish restores the finish without removing any of the existing finish Before you go to the extreme of stripping it, restore it.

For over 50 years, Howard's Restor-A-Finish has been a standard in the antique industry. Because Restor-A-Finish preserves and restores beauty to the original wood finish, it helps preserve the antiques’ authenticity and value, whereas stripping the finish may literally strip the piece of its value. Restor-A-Finish helps faded lacquer, shellac, varnish, polyurethane, and most other wood finishes by bringing back the original color and luster. It restores the depth of grain in wood finishes, going much deeper than temporary “scratch cover” products. Restor-A-Finish penetrates and permanently restores most wood finishes without removing any of the existing finish - this is why it is very popular for antiques. Restor-A-Finish maintains the original "patina" of an antique finish, maintaining its character and value as an antique. To protect the newly restored finish Feed-N-Wax is recommended as a follow-up to Restor-A-Finish.

“Restore It – Don’t Strip It!”

Permanently revive and restore the original color and luster in one step, without removing any of the existing finish. Most wood finishes that seem to need a complete refinishing job can be completely restored in a few minutes with this simple wipe-on, wipe-off process. White heat rings and watermarks, sun fade, oxidation, smoke damage, and most other blemishes can be quickly blended away. Before you go to the extreme of stripping it, try restoring it!

Restor-A-Finish is a unique finish-penetrating formula that contains a small amount of stain combined with just the right amount of solvent and restoring oils, giving it the unique ability to penetrate and permanently restore most existing finishes without removing any of the existing finish.

Directions:

• Choose the color of Restor-A-Finish that best matches the finish of your wood. Test on an inconspicuous area. Apply with a small pad of cloth, cover a small area at a time and immediately wipe dry. Do not pour directly on finish. To remove stubborn white rings, oxidation, or light scratches, apply Restor-A-Finish with a pad of super fine (0000) steel wool. Finishes vary in hardness, so test pressure to be used with (0000) steel wool on an inconspicuous spot. Rub lightly in the direction of the wood grain until blemish is blended away. Cover a small area at a time and wipe dry. To protect and maintain the newly restored finish, follow up with Howard Feed-N-Wax.
• When using a soft cloth or steel wool, rub with light pressure but hard enough to blend away the damage. As you restore the finish be sure to periodically check your progress. Always rub with the grain of the wood. Some dry faded finishes will only require a quick wipe-on, wipe-off application and will quickly absorb Restor-A-Finish. Other finishes will require a little more work. Still other finishes may require leaving the Restor-A-Finish on longer so it can penetrate into the finish and restore color and depth of grain deep into the wood.  All finishes are different, so testing first may be required. Always wipe off excess Restor-A-Finish.
• After wiping Restor-A-Finish dry, wait at least 30 minutes and then apply a coat of Howard Feed N Wax to protect and maintain the newly restored finish. Then re-apply as needed, or when the finish starts to look dry.

Treating carved woods:

Restor-A-Finish has saved many hours of labor by quickly restoring color and depth of grain on carved wooden furniture, clocks and picture frames. Simply apply Restor-A-Finish with a small paintbrush or soft toothbrush and wipe dry.

Tip: 

 If a high gloss finish should appear dull due to the use of steel wool, polish it out with Restor-A-Shine Polishing Compound. Restore-A-Shine is perfect for the final step in restoring high gloss finishes by buffing away fine scratches only seen in the light.  These super fine lines in the finish from a distance creating the look of “dullness” on high gloss finishes and can be easily buffed away with Restor-A-Shine Polishing Compound.