Matek H743-Slim V4 Flight Controller - 30x30mm

Matek H743-Slim V4 Flight Controller - 30x30mmMatek H743 Slim V4 is a high end flight controller designed for freestyle and long range drones powered by 28S LiPo batteries. It offers wide compatibility with Betaflight, iNav, and ArduPilot firmware. The board is built around the powerful H743 processor combined with two ICM42688P gyroscopes for precise motion data and a DPS368 barometer for altitude measurement. For analog video, it includes an OSD chip and a microSD slot for Blackbox logging.

Matek H743-Slim V4 is a high-end flight controller designed for freestyle and long-range drones powered by 2–8S LiPo batteries. It offers wide compatibility with Betaflight, iNav, and ArduPilot firmware. The board is built around the powerful H743 processor combined with two ICM42688P gyroscopes for precise motion data and a DPS368 barometer for altitude measurement. For analog video, it includes an OSD chip and a microSD slot for Blackbox logging.

What is new on the H743-slim-V4

• Increase the output current of BEC5V from 2A to 2.5A, and raise the filtered VBAT current from 1A to 2A.
• Add TVS protection on Input voltage
• Add protections on more MCU I/O.
• Replace DPS310 with DPS368(environmentally protected against water (IPx8), dust & humidity)
• Other functions, Pins/Pads layout are same as previous board version.

Check out all our 30x30mm Flight Controllers and the rest of our Matek Products!

Betaflight / Inav Mapping Details

ArduPilot Mapping Details

Specifications

• MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash
• IMU: Dual ICM42688P
• Baro: DPS368
• OSD: AT7456E (SPI2)
• Blackbox: MicroSD card socket

• 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
• 13x PWM outputs(including “LED” pad)
• 2x I2C
• 1x CAN
• 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)
• 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
• 1x SPI3 breakout
• USB Type-C(USB2.0)
• 1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
• 1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)

• Dual Camera Inputs switch
• 5V 0r Vbat(2A) filtered power ON/OFF switch

• DJI FPV OSD is supported by any spare UART

Power

• Vbat Input: 6~36V (2~8S LiPo) with TVS protection
• BEC: 5V 2.5A cont. (Max.3A)
• LDO 3.3V: Max.200mA
• VBat filtered output 2A for VTx and camera
• No Current Sensor built-in
• ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)
• Static power: 200mA@5V with Betaflight,  150mA@5V with ArduPilot

FC Firmware

• ArduPilot: MATEKH743
• BetaFlight: MATEKH743
• INAV: MATEKH743

Physical

• Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
• Dimensions: 36 x 36 x 5 mm
• Weight: 7g

Package Includes:

• 1 x H743-SLIM-V4
• 6 x Silicon grommets M4 to M3
• 1 x JST-SH1.0_8pin cable, 5cm
• 2 x JST-SH1.0_8pin connectors
• 1 x JST-GH-4P to JST-GH-4P cable for CAN port, 20cm