SKU: 49759339681

Blackmagic Design Spares - Camera Studio Pro - PCB Main 6K

Sale price$13698.75 Regular price$15220.83
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 11 - Jul 16

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Blackmagic Design Spares - Camera Studio Pro - PCB Main 6KThe Blackmagic Design Spares Camera Studio Pro PCB Main 6K is the core processing engine for the Blackmagic Studio Camera 6K Pro. This board is the most significant electronic component in the camera, as it handles the massive data throughput of the 6K sensor, the advanced color science, and the broadcast specific features like remote tally and talkback. Because the Studio 6K Pro is a specialized broadcast unit, this PCB is distinct from the Pocket 6K

The Blackmagic Design Spares - Camera Studio Pro - PCB Main 6K is the core processing engine for the Blackmagic Studio Camera 6K Pro. This board is the most significant electronic component in the camera, as it handles the massive data throughput of the 6K sensor, the advanced color science, and the broadcast-specific features like remote tally and talkback.

Because the Studio 6K Pro is a specialized broadcast unit, this PCB is distinct from the Pocket 6K or URSA series, featuring specific hardware for professional live production.


Core Responsibilities

The Main PCB serves as the command center for the following broadcast-critical functions:

  • Image Processing: Houses the FPGA that processes the 6K sensor data to deliver the "Generation 5" color science, optimized for live grading via an ATEM switcher.

  • Tally & Talkback Logic: Manages the communication signals coming through the SDI or Ethernet (PoE) ports to trigger the tally light and the 5-pin XLR headset system.

  • Connectivity Hub: Directly interfaces with the high-bandwidth ports, including 12G-SDI, 10G Ethernet, and the dual USB-C ports for external recording and focus/zoom demand.

  • ND Filter Control: In the Pro model, this PCB drives the motorized internal ND filters.

When to Replace the Main PCB

This is a high-level repair typically reserved for units that have suffered total system failure:

  • "Dead" Camera: The camera fails to power on via DC, XLR power, or PoE (Power over Ethernet), and the internal power cables have been ruled out.

  • SDI/HDMI Controller Failure: If the camera functions but cannot output a signal to a switcher, and the physical ports are not loose, the surface-mounted controller chips on the PCB are likely damaged.

  • Talkback/Audio Buzzing: If the 5-pin XLR talkback system develops a digital "hum" or fails to transmit audio while the headset is known-good.

  • Ethernet/PoE Failure: On the 6K Pro, the 10G Ethernet port is a common point of high-voltage intake; a surge via a network switch can fry the Ethernet controller on the Main PCB.


Key Features

  • Genuine OEM Part: Pre-configured for the 6K Studio sensor's specific timing and voltage requirements.

  • Broadcast Integration: Includes the hardware necessary for remote camera control (shutter, iris, color) via the SDI return feed or Ethernet.

  • Direct Mount I/O: Most of the professional connectors are soldered directly to this board to minimize signal latency.


Technical Installation Note

DANGER: Level 4 (Expert) Repair. The Studio Camera 6K Pro is physically large but internally very dense.

  1. Thermal Dissipation: Like all 6K models, the Studio Pro generates significant heat. You must apply fresh thermal paste or replace the specialized thermal pads between the processor and the internal heat-pipe assembly.

  2. Ribbon Cable Management: There are several long ribbon cables connecting the Main PCB to the 7-inch high-brightness screen and the side control panels. These are under slight tension and can easily snap if the chassis is opened too aggressively.

  3. Sensor Alignment: The Main PCB connects directly to the sensor block. During replacement, ensure the sensor remains perfectly parallel to the lens mount; even a slight tilt will cause "soft corners" in your image.

  4. Static Discharge: This board contains high-speed 10G and 12G data lanes that are extremely sensitive to ESD. Always use a grounded wrist strap and an anti-static workspace.

Expert Advice: If your 6K Studio Pro is acting up, check your PoE+ or PoE++ switch settings. Often, "board failures" are actually just the camera not receiving enough wattage from the network switch to power both the processing board and the 1,500-nit screen simultaneously. Always test with the dedicated 4-pin XLR DC power supply before concluding the Main PCB is dead.

Are you experiencing a total loss of power, or is the camera failing to be "seen" by your ATEM switcher via SDI or Ethernet?

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 49759339681

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.4 ★★★★★
Based on 549 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
J
Verified Purchase
Joseph
West Palm Beach, US
★★★★★ 3
DIY fit
Eventually I got one of em to fit but overall too limited on options.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 26, 2025
D
Verified Purchase
DebraLee Miller
Lowell, US
★★★★★ 5
Worked
Worked for exactly what I needed it for. Fit perfect once I found the right one. Held my headlight in tight just like the original
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 26, 2025
K
Verified Purchase
Kristen
Pawtucket, US
★★★★★ 4
Good
As advertised
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 8, 2025
I
Verified Purchase
ismael
West Palm Beach, US
★★★★★ 1
Does not fit 330i , xenon headlights clips
Bottom length isn't wide enough, not for 330i ,xenon retainer. I went to the junkyard got 4 clips for a dollar. Im going to see I can return them.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 18, 2023
L
Verified Purchase
lowell t hoyland
Draper, US
★★★★★ 5
Everything I expected
Shift quick right parts
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 20, 2025

recommand products